Skip to content
EchoPlace Garage Door Specialists
Open 24/7(226) 400-9783Open 24/7
Detached coil springs with end fittings and a cable rest on a bench in front of a closed garage door. — Torsion Spring Replacement, Brantford
Gloved hand holding a white garage-door roller beside its track, with two loose rollers and a red tool on a tray. — Garage Door Roller Replacement, Brantford

Springs · Brantford

Torsion Spring Replacement

You heard a sharp bang from the garage, and now the opener hums for a second and gives up.

Call (226) 400-9783

In plain words

On a door with two springs, replacement usually starts with a conversation about scope. Both springs have completed the same number of cycles, so when one breaks the other is typically close behind, and replacing the pair together gives the door two matched springs sharing the load evenly. The technician explains what the installed system is, how each spring is loaded and what the door's weight calls for, then fits and winds the springs as a set. The result is a balanced door with a fresh cycle life on both sides rather than a repair that may be repeated soon.

Sound familiar?

The door drops the last stretch to the floor rather than settling, and when you stop it halfway by hand it slides down instead of staying put. Balance has drifted, and the spring is no longer holding its share of the weight.

How the visit goes

Torsion Spring Replacement

How the visit goes

Technician kneeling at a white garage door, turning a screwdriver on a black handle latch mounted on a vertical steel strip.
Technician kneeling in a blue cap, fastening a metal hinge plate to a gray ribbed door panel with a red drill.
  1. Weighing the door honestly

    A spring is chosen for a specific load, so the technician establishes what the door actually weighs rather than guessing from its appearance. With the opener released and any remaining tension safely removed, a scale under the bottom section gives a real figure. Construction is recorded alongside it: single-skin steel, insulated steel sandwich, solid wood, glass panels or an aluminum frame all sit at very different weights for the same size. Extras count as well, including added windows, a heavy bottom seal or panels replaced over the years. That weight, with the door's height, is the basis for the spring specification.

  2. Balancing the door by hand

    Once the clamps are off, the technician lifts the door by hand to about waist height and lets go. A balanced door stays where it is, or drifts only slightly. If it rises on its own, the spring has a little too much tension and is eased a quarter turn; if it drops, a quarter turn is added. The door is then run through its full travel, watching that both sides move together and the sections stay flat in the tracks. This is repeated until the door feels light and stops cleanly at several heights, which is the standard the whole job is measured against.

  3. Using the manual release with confidence

    A balanced door is also a door you can operate safely by hand when the power is out. Pull the red release cord with the door closed to free the trolley, then lift the door with both hands on the handle or the bottom section; it should rise smoothly and stay open at full height. To re-engage, pull the cord toward the door until the trolley clicks back onto the carriage, or simply run the opener, which reconnects on most models. Because the spring now carries the weight, this is light work, and it is the recommended way to get a vehicle out during an outage.

Torsion Spring Replacement

In the van

  • Cable drums

  • Wire gauge and tape measure

  • Socket set and wrenches

  • End bearing plates

  • Centre bearing bracket and bearing

Technician in an olive cap pointing a yellow-handled screwdriver at the wiring of a ceiling opener above a windowed door.

Torsion Spring Replacement

What affects the quote

  1. Drum type and lift configuration

    Standard-lift drums are the common case. High-lift, vertical-lift or low-headroom arrangements use different drums, cable lengths and turn counts, which changes the parts and the time involved.

  2. Door size and weight

    A double-width door, a solid wood door or a thick insulated door weighs far more than a single-width steel panel, calling for heavier wire, longer coils or more springs to balance it.

  3. Spring finish

    Oil-tempered and galvanized springs suit different garages. A coated or galvanized spring for a damp or salt-exposed space is a choice the customer can make when the specification is discussed.

What to have ready

  • Do you know the door's age or when the springs were last replaced?
  • Can you see a gap in the spring above the door?
  • Did you hear a loud bang before the door stopped working?
Call (226) 400-9783

Torsion Spring Replacement: questions

Questions
How do you know which spring my door needs?

The spring is chosen from measurements rather than appearance. The technician records the door's width, height and weight, the drum type and track lift, and reads the old spring's wire size, inside diameter, length and wind direction. Those inputs together determine the spring that will balance the door. The choice is confirmed on the spot by lifting the finished door by hand and feeling it hold at mid-height.

What is the difference between torsion and extension springs?

Torsion springs mount on a shaft above the door and twist to store energy, lifting the door through cables and drums. Extension springs run alongside the horizontal tracks and stretch as the door closes, pulling it up through pulleys. Torsion systems tend to lift more evenly, take up less space beside the tracks and are the standard on most modern doors. Both are professional service items because of the energy they hold.

Why is my door sitting crooked since the spring broke?

On a two-spring door, one intact spring keeps pulling on its side while the broken side goes slack, so the door lifts unevenly and a cable can jump its drum. The technician levels the door, reseats the cables in their drum grooves and evens the tension after the new spring is fitted. Rollers and track are checked for damage from the crooked travel so the door runs square again.

Related services

Torsion Spring Replacement near you

Call(226) 400-9783

Request a visit

Or call (226) 400-9783 · open 24/7